Category Archives: Insulation Boards

Polystyrene Boards EPS

Polystyrene Insulation Boards EPS 100

High pressure resistant thermal insulation board made of expanded polystyrene foam.

Color: White
Surface: 0.5m x 1m, 1m x 1m, 1m x 2m
Thickness: 2cm to 30cm
Compressive stress (at 10% compression): 100kPa
Flameability: B1 (hard burning)

Apparent density EPS 100: 18 – 22 kg/m³
Thermal conductivity: λD = 0.038 W/(mK)

Application: Thermal insulation board for areas with high pressure loads (under floor, the flat roof, sloping roof, under floor heating, refrigerators).

Roof Floor
Advantages: Good thermal insulation properties, low water absorption and dimensional and shape stability.

EPS 100

Polystyrene Insulation Boards EPS 150

High pressure resistant thermal insulation board made of expanded polystyrene foam.

Color: White
Surface: 0.5m x 1m, 1m x 1m, 1m x 2m
Thickness: 2cm to 30cm Compressive stress (at 10% compression): 150kPa
Flameability: B1 (hard burning)

Apparent density EPS 150: 22 – 33 kg/m³
Thermal conductivity: λD = 0.034 W/(mK)

Application: Thermal insulation board for areas with high pressure loads (under floor, the flat roof, sloping roof, under floor heating, refrigerators).

 Roof Floor

Advantages: Good thermal insulation properties, low water absorption and dimensional and shape stability.

XPS ODE

Polystyrene Insulation Boards XPS

Pressure-resistant thermal insulation board (XPS) made of extruded polystyrene foam with shiplap. The XPS insulation board provides energy savings, thermal insulation, from the basement to the roof.Just where extreme pressure and moisture stress, particularly high demands on the insulation materials, the extruded polystyrene (Short form XPS, named after extruded polystyrene foam) is the ideal solution for numerous applications. Such as perimeter and base insulation, flat roof insulation, insulation under the soil plate, in wet areas, etc. XPS AustrothermXPS ODE

Color: green ODE, pink Austrotherm
Thickness: 3cm, 5cm, 10cm Surface: 125cm x 50cm
Available surface: 0,75m²/board
Flameability: B1 (hard burning)
Compressive stress (at 10% compression): 300kPa

Apparent density XPS: 30 – 45 kg/m³
Thermal conductivity: λD = 0,033 – 0,037 W/(mK) 

Application: Basement wall outside, above and below ground-plate, for inverted roof, terrace- and parking-roof, in a humid area, Plus Duo-roof, Core insulation.

Floor Skirting board Basement floor Basement wall

Advantages: largely water resistant, best ecological property (cell content air), excellent thermal insulation, suitable for promoted residential building.

Austrotherm polystyrene EPS-F70

Polystyrene Insulation Boards EPS – F70

Thermal insulating boards made from blocks of expanded polystyrene beads. System component of the Baumit External Wall Insulation System EPS.

Color: White
Surface: 0.5m x 1m, 1m x 1m, 1m x 2m
Thickness: 2cm to 30cm
Flameability: B1 (hard burning)

Apparent density EPS-F70: 15 – 18 kg/m³
Thermal conductivity: λ = 0.040 W/(mK) = 0.29 [BTU in /ft2.hr.°F]

Properties: Highly thermally insulating, dimensionally exact, form retentive and resistant to ageing, non-shrinking, hardly flammable. Free of CFCs, HCFCs and HFCs.

Application: As an exterior wall heat insulation composite system for the facade of newand existing buildings.

Facade

Advantages: Good thermal insulation properties,low water absorption and dimensional andshape stability.